Audon Press Releases

H0530 Ethernet thermometer alarm with relay outputs

2010-07-28T06:09:00.000-07:00

The H0530 is a low-cost Ethernet solution for Temperature monitoring and alarm in server room, data centre, museum, medical and industrial environment monitoring applications. Featuring a built-in temperature sensor with a -30°C to 80°C range, 3 digital inputs for use with PIR or flood detection devices, 2 alarm relay outputs, LCD for local display, email and SNMP under/over temperature/humidity alarm, a built-in webserver for real time temperature display and history chart and MODBUS protocol for SCADA compatibility.

http://www.audon.co.uk/h4531.html

GL220 Chart Recorder/ Data Logger

2010-07-28T05:42:00.000-07:00

The GL220 is the next generation midi logger following on from the success of the GL200 & GL200A models. With 10 fully isolated multi-function inputs and internal 3.5MB of non-volatile flash memory, this logger has an exceptional cost to performance ratio. With its large format colour display, you can easily set up and capture data with the ability to monitor waveforms and digital values during measurements. Its instant replay function makes it easy to review data that has been captured to internal memory or removable USB memory stick storage. Standard PC interface makes GL220 accessible through USB.

http://www.audon.co.uk/gl220.html

TME - Ethernet Thermometer Alarm Unit

2010-06-24T03:15:00.000-07:00

TME is a simple temperature sensor with Ethernet interface. It measures temperatures ranging from -55°C to +125°C. Measured values can be read in several ways including TCP, UDP, HTTP (WEB), e-mail, SOAP, Modbus TCP and SNMP protocols. Thanks to this it is possible to choose a method suitable for particular application.

The temperature is sent in a simple ASCII format directly in degrees Celsius; there is no need of any additional conversion. It also enables communication with SNMP protocol (UDP) or sending an e-mail in case any of the pre-set limits is exceeded.

You can easily embed the temperature from TME to your WEB site using http GET. Measured temperature is also available in XML file or it can be sent as an http POST in XML format for further processing in a WEB service. (All temperature acquisition methods are on page 6.)

TME is configurable via WEB interface. TME is powered from an external PSU 5V (TME) or directly from ethernet network according to IEEE802.3af standard (TME PoE)

http://www.audon.co.uk/tme.html

Replace your Relay Logic with low-cost mini PLC

2010-06-10T01:41:00.001-07:00

The xLogic SuperRelay is a compact and expandable CPU replacing mini PLCs, multiple timers, relays and counters. The xLogic SuperRelay perfectly fits in the space between timing relays and a low-end PLC's. The ELC-18 range is the advanced level model, incorporating a good mix of digital and analogue I/O, clock with calender, counters, timers, LCD, keypad and an expansion port. Easy to configure either using the LCD and keypad or with drag-and-drop functions blocks using the FREE ELCSoft software.

xLogic SuperRelay is a compact and expandable industrial computer ideal for replacing older PLCs, multiple timers, counters and traditional relay logic.

The xLogic SuperRelay is available in 120V/240V AC or 24V DC versions, making it the ideal solution for relay replacement, or simple control applications as building and parking lot lighting, managing automatic lighting, access control, watering systems, pump control, ventilation systems, home automation and a wide field of other applications demanding low cost to be a primary design issue.

Available with a common mix of digital input, digital output, analogue input, PWM output, high speed pulse counting, Real time clock and time switch functions. The ELC-18 range offer a 4-line LCD display and keypad for program modification and display and control whilst the program is running. An expansion port allows the connection of up to 31 expansion modules, extending the I/O channel count and adding Ethernet and SMS text communication capabilities.

http://www.audon.co.uk/elc18.html

Low Cost Ethernet to Serial Converter

2010-06-08T03:38:00.000-07:00

The eNET-232 Ethernet to Serial converter is a simple way of connecting any serial device, whether RS232 or RS485 to a Ethernet network. It features a simple setup procedure, ease of operation and automatic network recovery. Supplied with Programming examples and Virtual Serial Port software, to seamlessly add serial ports to your Network. The eNET-232 has a two serial ports, one RS232 and the other can be a RS232/422/485 RS485 port.

A pair of eNET-232's can be set up in Client-Server mode where they will send RS232 data between each other without any PC intervention.

http://www.audon.co.uk/data_comms.html

MODBUS Temperature, humidity and Barometric Pressure Transmitters

2010-05-10T01:55:00.000-07:00

Available from Audon Electronics are a range of low cost temperature, humidity and barometric pressure sensors with an RS485 output. These units can communicate via a simple ASCII "Adam 4000 series" compatible protocol or the industry standard MODBUS RTU protocol for use with common SCADA software.

Measured temperature, relative humidity, barometric pressure are converted to serial output with a RS485 interface. Transmitters are available in wall-mount, duct-mount and bar types. Also, types with T+RH probe on a cable are available.

They featuring a large dual line LCD for local display of temperature, humidity, pressure or other calculated value and the microprocessor design ensures maximum long term stability and fail indication.

The transmitter works with ModBus RTU communication protocol or with ADAM compatible ASCII protocol. The protocol is user selectable in special configuration mode by means of the PC.

http://www.audon.co.uk/temp485.html

Economical Ethernet Temperature/Humidity email Alarm

2010-05-06T03:31:00.000-07:00

The HWg-STE web thermometer is an Ethernet based two channel alarm unit configured using a built-in web server. The HWg-STE web thermometer is configured using a built-in web server which can also show the current temperature (and humidity). If the temperature (or humidity) exceeds a specified threshold, an e-mail alert is sent. The HWg-STE Thermometer is also fully SNMP compatible. Free windows software HWg-PDMS for datalogging, graphical overview and MS Excel export is included.

The HWg STE represents an effective and economic solutions in the applications like air-conditioning failure, heating system monitoring, cooler/freezer monitoring, heating optimization and food storage.

http://www.audon.co.uk/ste.html

Digital Event Recorder - Date and Time stamp 4 digital inputs

2010-02-18T04:37:00.000-08:00

The S7841 is a 4-channel digital event recorder which can record the date and time when any of it's 4 inputs changes state. The inputs can be volt-free contacts, such as door contacts, machine switches, or it can be a voltage signal. Data can then be downloaded to a PC for storage and analysis. A LCD display shows the current sate of the logger.

The S7841 is a stand-alone device, and the replaceble internal battery typically lasts 4 years. Up to 16254 events can be recordered per input, and spikes of less than 1/2 second are ignored to prevent false results.

Data download is via a Rs232, USB or Ethernet connection.

More Information from http://www.audon.co.uk/s7841.html

DLP-IO20 - USB DAQ just got cheaper!

2010-01-14T08:10:00.000-08:00

The DLP-IO20 Data-Acquisition Module from Audon Electronics is a low-cost, easy-to-use data-acquisition system for analyzing AC voltages, driving 5-volt relays, controlling and monitoring processes and measuring DC voltages in the range of 0-5 volts. This module provides topside wire terminal blocks for the wiring connections.

The 20 channels on the DLP-IO20 are broken down as follows: 3 outputs with high current relay/LED drivers and 17 digital I/O; 14 of which can be set to analog input mode. The DLP-IO20 also provides two latching relay contacts. Each of the channels and relay contacts can be controlled via simple, multi-byte commands. All operational power is taken from the host PC via the USB port.

The mode of each I/O is automatically changed with each command sent. For example, if an I/O is set to Digital Output-High and then the Digital Input Mode is selected, the I/O is first changed to Input Mode and then the high/low state is read and returned to the host.

http://www.audon.co.uk/io20.html

Internet Control and Monitoring Made Easy

2009-11-17T01:59:00.000-08:00

The IO-204 Monitor & Control Module helps bridge the gap between the physical world and the World Wide Web. The IO-204 module and online tools allow you to easily get your projects on the web. There is no need to run a home web server or track ever changing dynamic IP addresses.

The IO-204 module takes care of the Internet connectivity and the user customizable widgets on the ioBridge website remove the need for complex programming. Just plug in your IO-204 module, register on the ioBridge website and within minutes, you’ll be interacting with lights, switches, servos and sensors. Keep your widgets private on your secure ioBridge dashboard or publish them on your website for the entire world to enjoy!

http://www.audon.co.uk/iobridge.html

DSO and Logic Analyser in One

2009-07-13T02:07:00.001-07:00

The MSO7102 from Audon Electronics is a new, low-cost, full-featured two-channel bench top mixed-signal oscilloscope combined with a 16-channel logic analyser - perfect for any engineer or student’s desk.

With its 500MSPS 100MHz bandwidth, this instrument is perfect for design, testing and maintenance in the laboratory or workshop. Featuring a large high-resolution 8in colour LCD screen, advanced trigger functions, optional battery pack for portable applications and USB connectivity with free software. Available from stock for only £749 ex VAT

http://www.audon.co.uk/mso7102.html

IO-204 - Internet Control and Monitoring made Easy

2009-07-10T03:56:00.001-07:00

The IO-204 module takes care of the Internet connectivity and the user customizable widgets on the ioBridge website remove the need for complex programming. Just plug in your IO-204 module, register on the ioBridge website and within minutes, you’ll be interacting with lights, switches, servos and sensors. Send email or Twitter Mail on alarm or digital state change, chart and log sensor data and download to a Spreadsheet compatible file.

Wide range of expansion boards available - servo control, temperature, relay, X10www.iobridge.co.uk

Handheld Temperature/Humidity Dataloggers

2009-06-19T04:51:00.000-07:00

The D-Series available from Audon Electronics are a range of portable, battery operated stand-alone temperature, humidity and thermocouple data loggers. There are 3 models in the range; The D3120 has an internal temperature and humidity sensor with a -10°C to +60°C temperature range and a 5 to 95% relative Humidity range, the D3121 uses an external temperature and humidity sensor on a 1m lead with an -30°C to +105°C temperature range whilst the D0321 accepts up to 2 external type K, J, or S thermocouples.

Temperature and humidity readings can be displayed on the LCD screen and recorded in internal memory. An audible alarm can also be set to warn of alarm conditions.

Record rates can be set from once every 10 seconds to once every 24 hours, and up to 16000 recordings can be stored. Data can then be downloaded to a PC for display and analysis at a later date using the included software.

http://www.audon.co.uk/dlog.html

Temperature Alarm and Monitor from Web Browser

2009-06-18T01:48:00.001-07:00

The P8 series from Audon Electronics a low-cost Ethernet solution for temperature monitoring and alarm in server room, museum, medical and industrial applications. Simply connect to your LAN, open any web browser and begin monitoring.

Temperatures can be viewed in tabular or history chart formats. The history memory can hold 900 readings, with a variable store rate from 10 seconds to 18 hours. Stored history data can be downloaded to a PC file for further analysis.

The P8 series also have under and over temperature alarms. The units can email a warning message to up to three users, and can send SNMP alarm traps. The series also supports MODBUS TCP for integration with SCADA software. LabVIEW examples are available.

http://www.audon.co.uk/p8.html

New U6 adds to the LabJack Family

2009-06-17T10:56:00.000-07:00

The LabJack U6 USB Data Acquisition and Control unit from Audon Electronics is the newest member of the popular LabJack range. Featuring 14 analogue inputs with 16-18 bit resolution and a programmable gain amplifier, the U6 is ideal for measuring real-world signals.

The U6 has built-in cold junction compensation for thermocouples, and has two fixed current sources, useful for measuring resistance and for use with resistance thermometers.

Coupled with 20 digital I/O, up to 4 counter/timers, 2 analogue outputs, wide software support and a free copy of DAQFactoy Express, the U6 represents great value at only £219 ex VAT.

http://www.audon.co.uk/u6.html

Circuit Gear 7-in-1 USB Test Instrument

2009-03-18T03:22:00.000-07:00

The Circuitgear CGR-101 from Audon Electronics is a PC-based instrument that provides the features of seven devices in one USB-powered compact box. The device offers the performance of a two-channel 10-bit 20MSa/sec 2MHz oscilloscope, a two-channel spectrum-analyser, and a 3MHz 8-bit arbitrary-waveform/standard-function generator with eight digital I/O lines. It also functions as a network analyser, a noise generator and a PWM output source. Its open-source software runs with Windows, Linux and Mac OS.

The CGR-101's oscilloscope capability provides a two-channel 10-bit -+/-0.25Vp-p to +/-25Vp-p 2MHz basic scope, but with sophisticated marker measurements, triggering (normal, auto, single-shot and pre-trigger) with time-base adjustable from 50ns/division to 100ms/division. With a 1k sample/channel data buffer, the user can even view pre-trigger signals.

The CGR-101's two-channel FFT spectrum analyser feature offers marker measurements, and when used with the internal signal generator, displays Bode plots and performs vector network analysis, showing gain and phase values.

The CGR-101's signal generator is an 8-bit 0.1Hz to 3MHz signal source, offering sine/square/triangle/ramp waveforms, as well as being capable of outputting arbitrary or preloaded waveforms such as ECGs. The user can enable the generator, connect its signal to a circuit and perform measurements with the oscilloscope and/or spectrum analyser. The generator can also be set to function as a white noise source. A slider-controlled PWM generator is also provided, with mark-space ratio clearly displayed.

The included visual interface software enables simple control and display of information. The oscilloscope, generator, and digital I/O are operated from a custom open-source Tcl/Tk software GUI included with the hardware. As the software is open source, the code can be read and even added to or customised.The CGR-101 is also Labview compatible and can be controlled by any serial-port-driving software, such as Matlab or Visual Basic.

Project-based electronics lab teaching materials are also available for use with Circuitgear CGR-101. http://www.audon.co.uk/cgr101.html

Price drop on PCI DAQ Cards

2009-03-13T02:08:00.000-07:00

Audon Electronics have reduced the price of the PCX range of PCI data acquisition and control cards. The range was designed with the industrial user in mind, and feature real-world interfaces such as relays, Darlington drivers and optically isolated inputs.

There are seven models available ex-stock, 4 digital I/O cards, a counter/timer card an analogue output card and a multifunction I/O card

All cards come with a comprehensive software development kit with a dll, ActiveX and numerous examples in Visual Basic and C++. Also included are LabView VI's and examples and Intouch drivers.

Prices start at just £99.

USB DAQ Range Expands with the USB-1208LS Addition

2009-02-06T03:29:00.001-08:00

Audon Electronics has now added the RedLab USB-1208LS to it's range of USB data acquisition and control units. The RedLab USB-1208LS has 8 single-ended inputs or 4 differential inputs with 12-bit resolution, offers sample rates up to 1.2 kilosamples/sec (8 ks/s for up to 4000 samples) with 8 software selectable input ranges. The unit also provides 2 channels of 12-bit analogue output, one 32-bit counter and 16 bits of digital I/O.

With the addition of the USB-1208LS, Audon Electronics now has one of the largest ranges of USB Data Acquisition and Control equipment in the UK with more than 30 different model types usually in stock for next day delivery.

DataNet Wireless Data Acquisition System

2008-12-01T02:31:00.000-08:00

The DataNet is a professional wireless data acquisition system using the Zigbee wireless protocol. Consisting of a USB base station, DataNet acquisition units, repeater units and the DataNet PC Suite logging software. The acquisition units have 4 inputs for direct measurement of PT-100, thermocouple, voltage 4-20mA, frequency and pulse. There is also a version with the addition of built-in temperature and humidity sensors.

Data can be stored in internal memory, or streamed to a central PC running the DataNet software for recording, charting and display. Data can be displayed in tabular or chart formats or the user can display a plant mimic with data overlaid. Logged data can be exported to a spreadsheet for further analyses. The software also enables you to configure, calibrate or update the firmware of DataNet units wirelessly.

http://www.audon.co.uk/datanet.html

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

TBox20 - Alarm and Control via your Mobile Phone

2008-11-26T04:14:00.000-08:00

The TBox20 is a low cost solution to Remote Control and Monitoring via your mobile phone. The TBox20 can monitor 2 analogue and 4 digital switch inputs. A SMS alarm message can be sent when inputs exceed preset limits. The user can also interrogate the inputs through SMS messaging. The TBox20 also has 4 relay outputs which can be activated via SMS and used to switch lamps, pumps, heaters etc

The Tbox20 is an advanced yet simplified Remote Terminal Unit. Taking advantage of the reliable, widespread GSM networks and the supported GPRS service, Tbox20 becomes a remotely accessible unit from any part of the world. Using an embedded feature rich web server interface, you can configure various parameters of Tbox20. The inputs present on Tbox20 can be used for monitoring of external devices or connecting sensors (analog/digital). Alarm conditions can be configured for monitoring of these inputs. Since Tbox20 supports SMS and SMTP protocols, the device can be configured to send SMS/Email whenever alarm conditions occur. Tbox20 also gives you the freedom to control the states of the connected outputs.

Available ex-stock £149 ex VAT and delivery

http://www.audon.co.uk/tbox20.html

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: sales@audon.co.uk
web: www.audon.co.uk

ARMWeb Web Server Controller Board programmed in BASIC

2008-11-25T06:55:00.001-08:00

The ARMweb from Audon Electronics is an ARM-7 based development board with an on-board Ethernet port and built-in web-server. Perfect for small web-based applications that require user customisation. Featuring 31 TTL compatible digital I/O's, 6 analogue inputs, 6 PWM outputs, an optional USB port and an easy-to-use web interface. The ARMweb has an easy-to-learn built-in BASIC compiler so you can be up and running in no time. Users can create and upload their own web pages and interact with the program code all using a web browser.

Available as board only or as an evaluation kit.

http://www.audon.co.uk/armweb.html

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: sales@audon.co.uk
web: www.audon.co.uk

Control any GPIB Instrument over Ethernet

2008-10-29T05:09:00.000-07:00

The GPIB-LAN controller from Audon Electronics converts any computer with a Ethernet port into a GPIB Controller or Device. In Controller mode, the GPIB-LAN controller can remotely control GPIB enabled instruments such as Oscilloscopes, Logic Analyzers, and Spectrum Analyzers. In Device mode, the GPIB-LAN controller converts the computer into a GPIB peripheral for downloading data and screen plots from the instrument front panel. In both modes, the GPIB-LAN controller interprets high level commands received from the host computer and performs the appropriate low-level GPIB protocol handshaking.

No special drivers are required and a wide variety of host software may be used to communicate with the GPIB-LAN. The GPIB-LAN controller supports static IP address and dynamic (DHCP) IP address. The controller’s network parameters can be configured using the supplied NetFinder application

Available ex-stock from only £149.

www.audon.co.uk/gpiblan.html.

Vortex Low Cost Wind Speed Sensor

2008-10-28T06:51:00.000-07:00

The VORTEX anemometer available from Audon Electronics is a rugged rotating cup-style wind sensor which can handle speeds from 5 to over 125 mph. The Vortex anemometer has a reed switch based volt-free contact closure output, producing one pulse per rotation, with a scaling of 2.5mph per pulse per second. This simple interface allows for easy connection to PC based data acquisition systems and stand alone dataloggers.

It comes with 8m of exterior grade cable which can be easily extended and an aluminium mounting bracket. Available as sensor only or sensor plus battery powered LCD display which gives readings in both mph or km/h.

The VORTEX wind sensor is great for do-it-yourself projects, marine applications, home weather station and wind power turbine location analysis applications.

Price is only £39 ex VAT.

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: sales@audon.co.uk
web: www.audon.co.uk

eDAM-9000 enables Modbus control over Ethernet

2008-10-23T02:24:00.000-07:00

Available from Audon Electronics is the EDAM-9000 range of low-cost Ethernet based industrial data acquisition and control RTU devices. The EDAM-9000 range is based on common 10/100 Ethernet networking standards and supports the popular Modus/TCP protocol. The EDAM-9000 also supports UDP protocol over Ethernet networking.

There are 6 models in the range covering voltage, thermocouple and PRT analogue inputs, digital inputs, pulse counting and transistor outputs. All have a wide 10-30VDC power supply range, full opto-isolation and are housed in robust DIN rail mount enclosures.

Users can easily add EDAM-9000 I/O modules to existing Ethernet networks or use EDAM-9000 modules in new or existing SCADA systems. Prices start from just £99 ex VAT.

http://www.audon.co.uk/edam9000.html

USB DAQ Unit Samples all Channel Simultaneously

2008-09-19T03:16:00.000-07:00

The RedLab-1608FS is a low cost 8 channel, 16-bit 50kHz data acquisition unit featuring simultaneous sampling on all input channels. The RedLab-1608FS is ideal for applications that require higher sampling rates per channel such as transient signal analysis or simultaneous acquisition of data for phase sensitive applications.

The RedLab 1608FS offers true simultaneous sampling of up to eight channels of 16-bit single-ended analogue input. This is accomplished through the use of one A/D converter per channel. The range of each channel is independently configurable via software. Eight digital IO lines are independently selectable as input or output.

Multiple-channel continuous sampling rates up to 100 kilosamples/sec total, where the maximum sampling rate per channel is 50 kilosamples/second (2 channels can be sampled at 50 kS/s, 3 channels at 33.3 kS/s, 4 channels at 25 kS/s etc.). A burst mode is also provided that allows 4 channels to be sampled at 50 kS/s each for up to 32,768 total samples. Input ranges of ±10V, ±5V, ±2V and ±1 volt are software selectable and each channel may be set at any of the four ranges independent of other channels.

A SYNC (synchronization) control line allows you to synchronize two RedLab 1608FS modules together to acquire data synchronously from 16 analogue inputs.

A 32-bit counter is capable of counting TTL pulses. The RedLab 1608FS is powered by the +5 volt USB supply from your computer. No external power is required.

Supplied with free chart recording software, and drivers for most DAQ packages and programming languages.

--
Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

PDS7102 100MHz 500MSPS Digital Oscilloscope

2008-09-17T01:53:00.000-07:00

The PDS7102 is a full-featured 100MHz two-channel bench-top oscilloscope with 8bit resolution, perfect for any Engineer’s or Technicians desk. With a large 7.8" 640 x 480 colour LCD, the PDS7102 is small enough and light enough to carry anywhere. With a buffer size of 6K samples, PDS7102 sampling range is 500MSPS with synchronous 8-bit sampling on both channels. Sensitivity range is 5mV/div~5V/div. The USB connection makes printing stored results easy.

The PDS7102 can automatically measure and display frequency and peak-peak/ rms/mean values, and cursors can be moved to make individual readings. A built-in self-calibration facility improves measurement accuracy. Video monitoring is also possible with triggering on NTSC/PAL/SECAM line or field waveforms.

The PDS7102 can store up to 4 waveforms for comparison with live inputs. A persistence control is available too which simulates old analogue scopes, to compare slow-moving waveforms with previous scans. X-Y display allows you to see phase changes. A+B and A-B maths capability is also included.

Accessories provided with the PDS6062 include two x1/x10 passive oscilloscope probes, CD manual, PC download software, mains power cable and a USB cable.

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

DAQFactory Starter Data Acquisition software

2008-09-10T03:55:00.000-07:00

Available from Audon Electronics is a new cut-down version of the popular DAQFactory data acquisition and control package called DAQFactory Starter.

DAQFactory Starter offers all the basic features of an HMI / SCADA software tool including data acquisition from a wide range of devices (limited to 16 I/O points), data logging to ASCII and binary files, three user definable screens with 44 screen components, powerful graphing and trending, plus Email and FTP out.

If you have a small application with less then 16 I/O points and don't need any of the advanced features of a full SCADA package, then DAQFactory Starter is probably just right for you. Plus, if your system grows, you can always upgrade. DAQFactory Starter is only £29.

http://www.audon.co.uk/daqfactory.html

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

Lowest Cost Ethernet to Serial Converters

2008-09-04T03:36:00.000-07:00

The eNET range of Ethernet to Serial converts, available from Audon Electronics, are a simple way of connecting any serial device, whether RS232 or RS485 to a Ethernet network. They feature a simple setup procedure, ease of operation and automatic network recovery. Supplied with Programming examples and Virtual Serial Port software, to seamlessly add serial ports to your Network.

There are presently 4 models in the range. The eNET-100 is the budget level model with a single RS232 or RS422/485 port. Housed in a robust plastic enclosure with mounting tabs, the eNET-100 is ideal for cost-sensitive applications. Next is the eNET-132. This has 2 serial ports, 1 x RS232 and 1 x RS42/485. The eNET-132 is housed in a robust metal enclosure and is suitable for industrial applications. A 6 port version is available in the form of the eNET-432; this has 4 x RS232 port and 2 x RS422/485 ports.

Finally, the eNET-132W is a wireless WiFi version of the eNET-100. This unit supports IEEE 802.11b/g, uses spread Spectrum Technology with full WEP 64-bit/128-bit data encryption and has a maximum transmission Rate of 54 Mbps. Prices start from just £65

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

CuWin 3500 WinCE Touch Controller

2008-09-03T04:11:00.000-07:00

Available from Audon Electronics, the CUWIN 3500 combines a 7" Colour graphic display and touch interface with a high efficiency industrial controller.

The CUWIN 3500 is a panel mount embedded controller with a 800 x 480 pixel, 260K colour graphics LCD touch screen and fast ARM9 32bit 266MHz processor. At the rear are RS232 and RS485 serial ports. The unit has one USB Host port for peripherals and one USB Device port to connect to a desktop for device access over ActiveSync. A standard Ethernet port is also provided. A SD card slot is available which can be used for application or data storage. The CUWIN 3500 contains a built-in speaker for mono sound and has a stereo audio jack.

The CUWIN 3500 is equipped with Windows CE 5.0 Embedded. Windows CE supports applications developed in Microsoft Visual Studio to create Windows CE ARM executables. Also supports the .NET Compact Framework which reduces development time by allowing the use of .NET functions.

Available ex-stock for £369 ex VAT and delivery.

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

RedLab-TC USB Thermocouple DAQ device at a Red Hot price!

2008-09-02T00:58:00.000-07:00

Available from Audon Electronics is the RedLab-TC, a new, low-cost USB based thermocouple data acquisition unit. The RedLab-TC provides eight temperature inputs, 8 bits of digital I/O, 500 V of isolation, and built-in ambient temperature sensing, for only £239. Supplied with free chart recording software, and drivers for most DAQ packages and programming languages.

The RedLab-TC has 8 fully differential 24-bit thermocouple inputs which support all of the common thermocouple types (J, K, R, S, T, N, E, B). The RedLab-TC performs all linearization and cold-junction compensation to yield a typical accuracy of better than ±0.5°C. Opto-siolation ensures wiring faults won't cause damage to your system. The 8 digital I/O can be used for simple control, alarm outputs or for monitoring contact inputs.

The RedLab-TC is supplied with TracerDAQ, a simple chart recorder and datalogger package, and is supplied with drivers for common DAQ Packages such as LabVIEW, RealView and ProfiLab-Expert.

The RedLab-TC’s combination of competitive performance, superior ease-of-use, and lowest cost make it the perfect alternative to the thermocouple-based temperature measurement products available on the market today.

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

PLC runs BASIC and Ladder

2008-07-22T04:47:00.000-07:00

The CUSB range from Audon Electronics are low-cost open-frame PLCs based on the CuBloc core processor running both BASIC and Ladder-logic programs.

There are 3 models in the range, CUSB-22R, CUSB-30R and the CUSB36R. These DIN-rail mount PLC's have a different mix of I/O, but all have mains relay outputs, opto-inputs, analogue inputs, PWM outputs, counter/timers, simple connections to a LCD and keypad and two RS232 ports. These can be easily reconverted for RS485 multi-drop use and the CUSB can be programmed for use as both MODBUS master or slave.

The CUSB PLCs use the FREE CublocStudio application for program development. With CuBlocStudio you can write your BASIC and/or Ladder programs, simulate and de-bug and download to the CUSB PLC. CuBlocStudio has Ladder logic monitor and Time Chart tools to help with debugging.

The CUSB PLC can handle a wide variety of small to big applications while using only a fraction of the space of a full-size controller at a fraction of the price.

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

Low Cost Wireless temp/Humidity Logging

2008-07-10T03:45:00.000-07:00

The TL Series is a wireless temperature and humidity logging system based on a USB based receiver base station and up to 50 remotely located transmitters. The TL series is suitable for a wide range of uses in both industrial and domestic applications. Over fifty wireless sensors can be installed and monitored by the USB base station and the included temperature logger software enables the monitoring and analysis of all the sensors separately.

The TL-300 is the entry level receiver whilst the TL-500 has stand alone data logging capability with 2Meg of built-in memory. There are several wireless sensors in the range covering indoor and outdoor temperature and humidity. The sensor range will be expended over time, with a CO2 sensor due out next. The sensors can be located up to 40m from the receiver and use the licence exempt 433Mhz radio band.

The easy to use Software presents the temperature measurements with time and date graphically. The Software keeps track of the data over several years and will log data (in the background) as long as your computer is running.

The logged measurements can be exported in several formats for further processing. The package includes a screensaver that dynamically displays the actual temperature for each sensor. An additional feature, when the software is installed, is Messenger software that enables temperature messages to be sent by email and to be published on a website. With an email-to-SMS service it is therefore possible to receive information from the temperature logger system on an SMS enabled device.

Available as starter kits which include either the TL-300 or TL-500 receiver, 2 wireless sensors, USB lead and software CD. Prices start from £56 ex VAT and delivery.

Audon Electronics
Phone: +44 (0)115 925 8412
Fax: +44 (0)115 925 9757
email: info@audon.co.uk
web: www.audon.co.uk

Fast USB DAQ Unit for Dynamic Applications

2008-04-28T01:56:00.000-07:00

New from Audon Electronics is the USB-AD16F high speed USB based multifunction I/O unit with 16 opto-isolated analogue inputs, 2 analogue output, 4 digital inputs and 4 digital outputs. Data can be acquired at up to 250kHz rate at 16-bit resolution. A range of analogue and digital expansion boards are also available. Supplied with a free copy of NextView4-Live software for data acquisition and control and a wide selection of Windows, MAC and Linux programming examples.

The USB-AD16f features 16-channel 16-bit analogue inputs with 4 programmable input ranges of ±10V, ±5V, ±2V, ±1V. With 250kHz sampling rate the USB-AD16f is perfectly suitable for dynamic applications such as noise and vibration measurements and impact testing. The galvanic isolation of the analogue inputs protects the measurement system and PC from accidents!

The 2 isolated analogue outputs are also at 16-bit resolution with a ±10V output range. For controlling and recording digital states 4 digital inputs and outputs each are available. An additional counter input allows pulse measurements.

All I/O are presented via two 37-way D-type sockets, one analogue and one digital. The user can connect to this directly or optional expansion boards are available. Also compatible with the MAL series of signal conditioning modules for connection of thermocouples, strain gauges etc. For use with USB 1.1 and 2.0 systems, up to 127 units can be connected to a single PC.

Drivers are available for Windows, MAC and Linux operating systems. The USB-AD16f is supplied with an Active-X component and comprehensive programming examples for use with most common programming languages. There are also VI for use with LabVIEW and there is a USB-AD16f component ion the ProfiLab programming package.

The USB-AD16f is also supplied with a copy of nextView4-Live data acquisition and control software. With NextView-Live, the user can acquire and analyse data, set analogue and digital outputs and read the status of the digital inputs. The user can create their own screens, with chart displays, text, alarm panels, output sliders etc.

The USB-AD - Where's the DAQ Unit?

2008-03-06T04:56:00.001-08:00

Available from Audon Electronics is the USB-AD USB based multifunction I/O unit which is so small it could be mistaken for a connector. The USB-AD has 16 analogue inputs, 1 analogue output, 4 digital inputs and 4 digital outputs all enclosed in a standard 37-way D-type connector housing. Supplied with a copy of NextView4-Live software for data acquisition and control and a wide selection of Windows, MAC and Linux programming examples.

The USB-AD is a low cost USB based multifunction I/O unit with 16 x ±5V 12-bit analogue inputs, 1 x ±5V 12-bit analogue output, 4 digital inputs and 4 digital outputs. Data can be acquired at up to 500Hz rate at 12-bit resolution. All I/O are presented to a 37-way D-type socket. The user can connect to this directly or optional expansion boards are available. Up to 127 units can be connected to a single PC.

Drivers are available for Windows, MAC and Linux operating systems. The USB-AD is supplied with an Active-X component and comprehensive programming examples for use with most common programming languages. There are also VI for use with LabVIEW and there is a USB-AD component icon the ProfiLab-Expert programming package.

The USB-AD is also supplied with a copy of nextView4-Live data acquisition and control software. With NextView-Live, the user can acquire and analyse data, set analogue and digital outputs and read the status of the digital inputs. The user can create their own screens, with chart displays, text, alarm panels, output sliders etc.

The USB-AD is available ex-stock for £79 (ex VAT and Delivery)

Modbus I/O Units for easy SCADA Integration

2007-10-25T02:34:00.001-07:00

Available from Audon Electronics is a new range of low-cost Modbus based remote IO units which provide a simple way of integrating analogue or digital signals to supervisory SCADA systems. There are several models in the range from voltage, current, thermocouple and PT-100 inputs, voltage and current outputs and digital and relay I/O. Supplied with the IO Studio configuration software. The optional DAQ Studio software can be used to provide a data acquisition, trending and alarm management interface for the PC. Also compatible with all SCADA packages such as DAQFactory.

A new line of Modbus based IO modules for data acquisition and other applications. These IO modules offer good reliability with a low-cost solution for distributed control applications. They are compact, easy to integrate with existing Modbus networks and simple to use for the end user. Various types of IO modules are available for different kinds of requirements. All IO modules have LED indications of IO status and fault diagnostics. All IO modules have an ioslated 2 wire RS485 interface. The use of Modbus RTU protocol allows for easy integration with most SCADA software packages such as DAQFactory.

There are 4 digital I/O modules, the 16DI has 16 digital inputs which also double as 32-bit pulse counter inputs, the 16DO has 16 open collector transistor outputs, the 4RO has 4 mains capable power relays, and the 8DIO is a combination unit with 8 digital inputs and 8 transistor outputs.

The analogue I/O modules include the 8AIIS and 8VIS which accept 8 x 4-20mA or voltage inputs, the 8TCS which accepts 8 thermocouples including ,K,E,T,N,B,S,R,mV, C,D and G types, the 6RTD which accepts 6 x 3-wire RTD temperature probes and the 8AOI and 8OV which are 8 channel 4-20mA and voltage output models. There is also the DAIO combination unit with 2 analogue inputs, 1 analogue outputs, 4 digital/counter inputs, 2 transistor outputs and 2 RTD inputs.

IOStudio is a free software package supplied with the units used to configure the communication settings for IO modules on the Modbus network. Once a module is detected, it is possible to view real-time data of the module directly on the PC and it can be used for diagnostic purposes too.

Available ex-stock, prices start at only £99.

USB Relay Units need no PSU

2007-10-11T03:13:00.000-07:00

The UDIN range are a low-cost range of USB relay, digital I/O units for desk-top, panel or industrial DIN rail mounting. They feature mains rated relays capable of switching mains 3A and fully opto-isolated digital inputs. They do not require any external PSU. All units come with both Virtual Com port drivers so that they can be used with most legacy software packages or with a .DLL for direct programming. Supplied with cable, test programs and programming examples.

The UDIN range consists of a USB interface, a micro-controller and relay outputs and/or opto-isolator inputs. The UDIN units are controlled by simple ASCII commands. The USB interface handles the USB protocols and present the ASCII commands to the micro-controller as serial data. The micro-controller then uses the commands to control the relays or report back input status.

There are 4 models in the range. The UDIN-8R has 8 relays, the UDIN-8I has 8 opto-isolated inputs and the UDIN-44 has 4 relays and 4 opto-isolated inputs. There is also the UDIN-16A which has 4 mains rated 16A relays and 4 opto-isolated inputs.

Most software packages that can send or receive ASCII data to a RS232 port should be able to control the UDIN range. The UDIN units comes with a Virtual Com Port driver, which installs a "Virtual" Com port on the PC. Software can then send and receive ASCII data to and from this Virtual Com port and thus to the UDIN unit. Typical packages that can be used include Windows HyperTerminal (and most other terminal emulator packages), data acquisition packages such as Profilab, DAQFactory, LabVIEW, DasyLab, VEE, TestPoint etc. and also most SCADA Software packages.

Programmers can bypass the VCP route, and use direct .DLL function calls instead. The UDIN units are supplied with a test application complete with all source code. Drivers are available for the Windows operating system, Linux, MAC and Win CE.NET

The UDIN range can be desktop, panel or DIN rail mount. The units will clip on to standard 35mm DIN rail. The DIN rail mounting clips may be extended to reveal 4mm screw holes for fixing to a panel or wall

GL800 - One-of-a-kind Data Logger/Chart Recorder

2007-10-05T03:59:00.000-07:00

The GL800 data logger and hand-held chart recorder is one of a kind in its ability to read up to 200 channels of temperature, humidity and voltage data. With its large format LCD display, you can easily set up and capture data with the ability to monitor waveforms and digital values during measurements. Its instant replay function makes it easy to review data that has been captured to internal memory or to a USB memory stick. Standard PC interface makes GL800 accessible through USB or a LAN using the standard network settings built in to GL800

The GL800 is a compact data logger come chart recorder, with an A5 footprint, providing excellent portability. The GL800 is fitted with 20 channels as standard but can be expanded from 20 to 200 channels with the optional expansion modules. All channels are isolated channel-to-channel and channel-to-ground. It has the ability to perform simultaneous measurement of voltage , temperature and humidity. It also supports such inputs as pulse (e.g. power, rpm and flow) and logic, in addition to voltage and temperature.

Two USB ports are provided, one for a USB memory device and one for linking to a PC. Commercially available USB memory devices may be used for direct capture of data. With a 512M device, users can capture data for up to 269 days (10 channels, 1 second sampling rate). An optional battery pack is available for use where mains power is unavailable. The battery pack allows up to 9 hours of operation.

All the GL800's functions can be accessed through the easy-to-use keypad and LCD screen. Single touch buttons for such tasks as display mode, setup and logging start/stop negate the need for complicated menu trees. The bright easy-to-read 5.7" colour LCD screen makes it even easier to review measurement settings, measured waveforms and digital values.

The GL800 is bundled with PC application software that enables measurements directly to a PC. In addition to waveform monitoring, this software provides other useful functions such as direct writing of data to an Excel file and report creation. The software also provides a Help display function for enhanced usability.

Budget LCD Oscilloscope has Advanced Features

2007-09-27T02:20:00.001-07:00

The PDS5022S bench Digital Storage Oscilloscope has been specifically designed as an entry level instrument for educational, hobby and budget-driven applications. Although low-cost, the PDS5022S is packed with a wide range of useful functions usually only seen on higher-end DSO's, such as video trigger and auto-measurement. The large full colour LCD display makes for a clear unambiguous waveform display.

The PDS5022S is a 100MSPS dual channel 8-bit DSO with a 25MHz bandwidth, featuring a large 7.8" 640 x 480 pixel colour LCD display. The PDS5022S has easy-to-use controls and a simple and clear menu system. A compact and robust design that will not take up too much bench space.

The PDS5022S has several display modes: Normal mode operates like a standard 'scope with simple manual control of timebase, triggering, etc. XY Mode is where CH1 is displayed on the horizontal axis and CH2 is on the vertical axis. When the oscilloscope is under the sampling mode in which no trigger is found, the data appears as light spots. There is also an Auto-set mode, that allows the Oscilloscope to display and measure unknown signals automatically. This function optimizes the position, range, timebase and triggering and assures a stable display of virtually any waveform.

There is also an Average Display mode where the displayed waveform is an average of a pre-set number of waveform samples. This can eliminate noise which can otherwise obscure readings.

The PDS5022S can perform 5 types of automatic measurements, such as frequency, cycle, average value, peak-to-peak value and root mean square value. Up to 2 types of measurement results can be display simultaneously on the screen. Standard Maths functions are also included such as adding, subtracting, multiplying or dividing calculation on CH1 and CH2 channel waveforms.

There are two triggering modes including Edge triggering and Video triggering. The Edge triggering is a mode by which trigger occurs at the triggering threshold value of the input signal edge. With the Edge triggering selected, the trigger happens on the rising or falling edge of the input signal. With Video triggering selected, the oscilloscope performs the NTSC, PAL or SECAM standard video signals field or line trigger.

Other Features include waveform storage where up to 4 waveforms can be saved in the HDS1022M's internal memory for comparison display or upload to a PC. Stored Data can be uploaded to a PC via RS232 or USB in bitmap or ASCII format.

The PDS5022S is supplied with carry case, scope leads, CD and manual and is available ex-stock for just £215.

Multifunction USB DAQ Unit is Cheap but Fast

2007-09-20T01:47:00.000-07:00

The U120816 is a very low cost USB data acquisition module which provides eight single-ended 12-bit analogue inputs, 16 digital I/O lines, two programmable pulse-width output channels, and one 16-bit counter channel. Analogue sampling rate is 32 ksamples/s maximum, with up to 13 ksamples/s for all 8 channels.

There are 8 single ended analogue input channels with an input range of 0-4.096V, 12 bit, so the resolution would be 1mv. The U120816 supports scan and streaming modes for data acquisition. The user can scan a single channel or scan multi-channels at once. In scan mode, the execution time is 8ms or 125Hz per channel. In streaming mode, the U120816 can start streaming data to the PC immediately or upon external trigger input, select through software. In trigger mode, a high state on the trigger line will start the data acquisition. The maximum throughput of streaming data varies with number of channels and they are also system dependant. Typically this is up to 32Ksamples/s for a single channel and 13Ksamples/s for all 8 channels.

There are 16 bi-directional digital I/O lines in U120816 module. Each line is software configurable to be either input or output high or output low. At power-up or reset, all lines are set to be input by default. All digital lines are 5V TTL and include a 470 ohm series resistor to provides over voltage/short-circuit protection. Each channel also has a 1M resistor connected to ground.

Thre is an external trigger line for streaming mode data acquisition. It is software configurable if the user wants to wait for this line. When in use, as soon as the line goes high, the device will start hardware timed data acquisition. This is a TTL level input.

There are two 10-bit PWM outputs in U120816. Software can set the period and duty cycle for each channel separately. The period is between 3 micro seconds to 333 micro seconds or the frequency is 333kHz to 3kHz. Duty cycle can be set between 0 – 100%. The PWM outputs can be used to light LEDs, drive motors, or convert to analogue outputs by adding an extra circuit.

The U120816 has a 16-bit counter. Software has the option to select if the counter should be reset after the read or not. The counter is incremented when it detects a falling edge followed by a rising edge. If you reset the counter while your signal is low, you will not get the first count until it goes high-low-high again.

The U120816 is supplied with the free application iDAQTest&Log. This package that can be used to test the U120816 device and log analogue input data and read back logged data for basic analysis. With this software, the user can browse through all the features in U120816, such as read single analogue channel, multiple analogue channels, streaming analogue input data continuously for display and log into file with or without external trigger, set DIO directions and read/write DIO states, set PWM output, read counter etc.

The U120816 also comes with a programming API iUSBDAQ.dll. This DLL can be called by third party applications. Programming examples are supplied in VB , ActiveX , dot net , C/C++ , Delphi, MacOSX. There is also a LabVIEW VI and program examples. Price for the U120816 is only £79

Ethernet based Environmental Monitor sends email Alarms

2007-09-12T08:08:00.001-07:00

The Poseidon 3268 is a simple Ethernet based stand-alone device which can send an email alarm when up to 4 monitored temperature or humidity sensors exceeds their defined range. The Poseidon 3266 also has 4 contact-closure inputs which can be used to trigger alarms on state change and there are 2 relay outputs which can be used to reset servers, or switch on a fan, etc.

Temperature or combined temperature/humidity sensors can be connected via RJ11 cable using the 1-wire protocol. Sensors are simply connected in a serial chain using RJ11 cable. These can be up to 10m away from the Poseidon 3268. You can assign a name to each sensor and also define high and low alarm limits. When the parameter goes outside these limits, the Poseidon 3266 can send user defined email alarm messages and toggle the output relays.

Once the Poseidon 3268 is connected to the LAN, you can run the free UDP setup utility, which will search the LAN to find all attached devices. You can then specify your desired Network address parameters. Once this is done, you can simply access the I/O data from a web browser. There is also a flash-based version.

All sensor's values as well as alarm status information are available from XML files (temper.xml) and any application can log it from XML tags. The Poseidon 3268 also supports the Modbus/TCP protocol, so it is easy to integrate with common SCADA packages such as DAQFactory.

Typical applications include monitoring conditions in server rooms, switch-boards, cold-storage buildings, freezers and fridges and other environmental monitoring tasks.

Budget GPIB to USB converter is Easy to USe

2007-09-11T06:22:00.001-07:00

The GPIB-USB4 controller from Audon Electronics converts any computer with a USB port into a GPIB Controller or Device. In Controller mode, the GPIB-USB controller can remotely control GPIB enabled instruments such as Oscilloscopes, Logic Analyzers, and Waveform Generators. In Device mode, the GPIB-USB controller converts the computer into a GPIB peripheral for downloading data and screen plots from the instrument front panel. In both modes, the GPIB-USB controller interprets high level commands received from the host computer and performs the appropriate low-level GPIB protocol handshaking.

While the GPIB-USB4 controller provides many of the same features as GPIB-USB controllers from other vendors, it is much easier to use. The GPIB-USB4 controller provides a virtual serial interface to communicate with instruments, while handling all GPIB protocol details for you. As a result, you can communicate easily with instruments using any terminal program instead of having to write custom programs using the vendor supplied library

The GPIB-USB controller can operate in two modes – Controller mode and Device mode.

In Controller mode, the GPIB-USB Controller acts as the Controller-In-Charge (CIC) on the GPIB bus. When the controller receives a command over the USB port it addresses the GPIB instrument at the currently specified address to listen, and then returns the received data to the PC. Controller mode is used to remotely control instruments and to download screen plots by sending plot commands from a host computer.

In Device mode, the GPIB-USB Controller acts as another peripheral on the GPIB bus. In this mode, the GPIB-USB controller configures itself as a GPIB Listener. All data received by the controller over the GPIB port is passed to the USB port. Device mode is used to download screen plots from the instrument front panel for rendering using plotter emulation software.

A wide variety of host software may be used to communicate with the GPIB-USB controller. Any terminal emulation program, such as HyperTerminal, can be used to communicate with the controller and instruments connected to it. Any programming language or environment that provides access to serial ports or allows interfacing to DLL may be used to develop custom applications. Graphical programming environments like National Instruments LabView, DAQFactory and Agilent VEE may be used as well. Finally, it is possible to use plotter emulation applications such as 7470.exe, PrintCapture and Plottergeist to render screen plots from any common HPGL plotter instruments.

The GPIB-USB4 is available ex-stock from Audon Electronics for under £100

PLC and Touch Screen Controller in One

2007-09-06T08:11:00.001-07:00

Audon Electronics now stock the CUTOUCH CT1721, an integrated Touch panel, 5.6" graphic LCD, and programmable embedded computer. Based on Comfile’s "PLC-on-a-chip" technology, the CUTOUCH CT1721 provides fast processing speed, 82 digital I/O ports, 8 channels of 10-bit A/D, 6 x 16-bit PWM outputs, and 80KB Flash Program memory so you can quickly develop HMI devices for industrial machines, factory temperature controllers, packing machines, robots, embedded control, and more!

Using the FREE Cubloc-Studio Software, the CUTOUCH CT1721 can be programmed in both Basic and/or Ladder Logic, allowing fast control, complex maths, dynamic touch-screen graphics, and fast data-communication protocols to be easily implemented. Ladder Logic, offers real-time sequential processing and Basic supplies the number-crunching power. Both the real-time processing powers of a MODBUS PLC and the 32-bit floating-point maths, graphic capabilities, and communication powers of Basic are now available in one product.

The free CuCanvas software can be used to draw graphics such as boxes, circles, and menu buttons with keypads. These simple graphics can be made to animate, say to show the rise and fall of liquid in a tank for example. For more complex graphics PixelStudio software allows the user to create up to 200 custom images.

The CUTOUCH CT1721 has 82 digital I/O ports with a mix of 32 opto-isolated inputs, 32 transistor outputs and 17 5V TTL I/O. A range of expansion modules are available giving mains relay outputs, motor control, Compact Flash data memory storage and wireless Bluetooth interfaces. Using an optional XPORT internet module, TCP or UDP packets can be monitored through the internet from anywhere, allowing users to update or provide customer service for products located anywhere in the world.

The CUTOUCH CT1721 has 80KB Flash Memory for Basic and Ladder programs, 28KB for data memory, a Real Time Clock, and one of the two RS232 serial ports can be used for download and debug. With 8 channels of 10-bit analgue input and 6 channels of 16 bit Pulse Width Modulated output, the CUTOUCH CT1721 is ready-made for lots of industrial applications. An internal battery provides safe data backup.

MODBUS Master and slave support is also included, making the CUTOUCH CT1721 ideal for customized industrial use.

A stater kit is available that includes the CT1721 controller, a paper manual, all software on a CD, interface cables and RS232 programming cable all for under £250

GL200 Portable LCD Chart recorder/data logger

2007-06-14T03:26:00.000-07:00

The GL200 available from Audon Electronics is a new compact light-weight data logger/chart recorder accepting 10 thermocouple, humidity and voltage analogue inputs. With its large format colour display, you can easily set up and capture data with the ability to monitor waveforms and digital values during measurements. Its instant replay function makes it easy to review data that has been captured to internal memory or removable USB memory stick storage. Standard PC interface makes GL200 accessible through USB.

The GL200 accepts voltage, temperature, humidity, pulse and logic signals. Channel-to-channel isolation means wiring errors or overloaded channels do not affect neighbouring channels. Sensors are connected via rear mounted screw terminals. The built-in 3.5M memory is non-volatile so that data is retained even if the power supply is interrupted.

Two USB ports are provided, one for a USB memory device and one for linking to a PC. Commercially available USB memory devices may be used for direct capture of data. With a 512M device, users can capture data for up to 269 days (10 channels, 1 second sampling rate).An optional battery pack is available for use where mains power is unavailable. The battery pack allows up to 6 hours of operation.

All the GL200's functions can be accessed through the easy-to-use keypad and LCD screen. Single touch buttons for such tasks as display mode, setup and logging start/stop negate the need for complicated menu trees. The bright easy-to-read 3.5" colour LCD screen makes it even easier to review measurement settings, measured waveforms and digital values.

The GL200 is supplied with a copy of the OPS022 software. The OPS022 program provides excellent control over most GL Series functions, allowing PC control. It also provides convenient data transfer from the GL Series to your PC, as well as converting measured data into file formats that can be used with spreadsheet applications, data analysis applications, and other software programs. Converted data can be easily processed in electronic spreadsheets and graphs using popular applications such as Excel

DSO-101 USB Digital Storage Scope

2007-06-14T03:21:00.001-07:00

The DSO-101 from Audon Electronics is an USB-powered digital storage oscilloscope with dual 20MS/s inputs and a 2MHz bandwidth that is small enough to fit in your pocket. The DSO-101 packs some powerful features including a hardware preamp, adjustable digital triggering, and 32kB memory depth on each of the two 8 bit input channels. The DSO-101 is powered by an open-source graphical user interface for Windows and Linux.

The DSO-101 is a general-purpose two-channel oscilloscope for the teaching, development and debugging of electronic circuits. Channels A and B are sampled simultaneously and stored in oscilloscope memory before being sent for display to the host computer. Consequently, they are always time aligned and triggered from the same trigger signal. The oscilloscope timebase frequency is derived from a crystal oscillator, so it can be expected to be precise and stable.

The fully functional, easy to use software supports multiple triggering modes, waveform scrolling, saving waveforms to a file, and cursor measurements. Source code is included. The user can add and modify the graphic user interface as desired.

The PC connects to the oscilloscope hardware via a USB cable so that no other power source is required. The USB interface emulates a serial port so that the oscilloscope may be accessed as a serial port device

EMB MEGA32 AVR Single Board Computer Board

2007-06-14T03:18:00.000-07:00

Available from Audon Electronics is the EMBMEGA32 embedded microcontroller board based on ATMEGA32 AVR microcontroller family. It is low cost and flexible, making it ideal as an embedded controller for industrial, automation, security and process control applications.

The board has 32 digital I/O ports, a mini buzzer, reset switch and one RS232 port. It also has a serial 256k EEPROM and a battery backed DS1307 real time clock. The board has a LCD connector for common character LCD modules, together with a contrast pot, power supply and current limit resister for LCD backlight. The EMBMEGA32 also has 8 x 10-bit analogue inputs for measuring real world signals.

All ports on the board are connected to IDC connectors and analogue input connections are also available using screw terminals. A range of relay and opto-input expansion boards simply plug-in to the IDC connectors. DC and stepper motor control expansion boards are also available. The EMBMEGA32 board measuring only 82mm x 82mm is a two-layer design intended for demanding industrial applications.

The board provides a standard 10-pin in-system programmer header for connection to a wide variety of AVR ISP programmers. Compatible with the Atmel AVR Studio Assembler and the BASCOM Basic Complier. BASCOM is an easy to use but powerful Basic complier for the Atmel AVR RISC processors as used in the Audon range of Single Board Computers and PLC-style embedded computer boards. It greatly simplifies program development with a feature-rich list of BASIC commands, has built-in simulation and programming tools. A 4k code limited version of BASCOM can be freely downloaded from the Audon Electronics website.

Blootooth Wireless Data Acquisition and Control

2007-06-14T03:14:00.000-07:00

The MFC-4422 is a Analogue and Digital multifunction I/O bluetooth interface for professional wireless control applications in data acquisition, automation and facility management applications. The Board has 2 Analogue inputs, 2 analogue outputs, 2 relays, 2 TTL outputs and 2 opto-isolated and 2 TTL inputs. Suitable for integration in machinery and office equipment. Supplied with FREE Windows and PDA Software chart display and datalogging and programming examples

The MFC-4422 has a rich mix of inputs and outputs; 2 analogue inputs suitable for measuring real world parameters such as temperature or pressure etc. 2 digital inputs, 2 digital/relay outputs and 2 analogue outputs. The 2 opto-isolated digital inputs can be used as counter inputs. Counter-states or frequency can be read out wirelessly, which makes it most suitable for metering applications like electricity, gas, water meters. Digital outputs comprise 2 Relays and 2 TTL outputs. Digital Outputs can be switched remotely. A time off delay may be set to switch off the outputs when connection to the board is lost. The MFC-4422-provides 2 analogue outputs. Each of those outputs are provided as both a voltage signal in the range of 0-5 VDC and as pulse-width modulated TTL (PWM) signal.

The MFC-4422 can be used as a dumb I/O device or it can be operate in stand-alone mode with 2 independent on/off or PID controllers. Each control channel comprises one analogue input and one output. For on/off control, the measured input signal is compared with threshold points to switch on or off a relay output. With PID control, the measured value is used by a PID algorithm to derive an analogue output signal. The PID parameters can be adjusted by the user. Thus the MFC-4422 can be used as a 2 channel alarm unit or used to accurately control a process.

The MFC-4422 is addressed by means of a simple ASCII instruction set, which can be employed with any common programming language. No specific bluetooth-programming knowledge is required. Messages between board and PC/PDA are exchanged in plain text. The bluetooth-connection is established over a so called virtual com-port. Programming of a virtual com port is identical to programming a standard hardware serial interface. Visual-basic examples for PC and PDA are delivered on a CD together with the board. Your PC or PDA has to have a bluetooth interface in order to be able to connect with the board.

The MFC-4422 is supplied with FREE Windows and PDA utilities - WCI-software. With the WCI-software, you are able to manage all board parameters and to read and write to the different inputs and outputs. Also includes a chart recorder style display for analogue inputs and data logging capabilities. Data is logged to a Excel compatible data file.
The MFC-4422 is also supplied with an ActiveX component and Windows and PDA VB programming examples.

Remote Control and Monitoring via your mobile phone

2007-06-14T03:12:00.000-07:00

The Audon Electronics GSM-8000 is a low cost solution to Remote Control and Monitoring via your mobile phone. The GSM-8000 can monitor 8 analogue and 8 digital switch inputs. A SMS alarm message can be sent when inputs exceed preset limits. The user can also interrogate the inputs through SMS messaging. The GSM-8000 also has 8 relay outputs which can be activated via SMS and used to switch lamps, pumps, heaters etc. The GSM-8000 is complete with an LCD display for local status display, keypad and built-in Dual Band Modem.

The GSM-8000 has 8 x 12-bit 4-20mA analogue inputs, compatible with industry standard sensor transmitters. The input signals can be converted into meaningful engineering units such as °C or RPM and displayed on the LCD screen. Each analogue input can be assigned a high alarm setpoint and a low alarm setpoint. Alarm activation notification is sent via SMS messaging to up to two different mobile phone numbers. The user can also interrogate the analogue input readings at any time by SMS messaging.

The GSM-8000 has 8 digital inputs which can also be used to trigger a SMS alarm message when a contact is made. Again, input status can be read through SMS messaging.

The GSM-8000 also has 8 mains-rated relays which can used for remote control purposes. The relays can be activated and their status checked all via SMS messaging.

Typical applications areas include Industrial process plant, security and building management systems, traffic/transport systems, freezer/furnace monitoring and water/gas/electricity plant monitoring and control.

USB DAQ Unit has Flexible I/O

2007-06-14T03:11:00.001-07:00

Available from Audon Electronics is the LabJack U3 low-cost USB multifunction data acquisition and control device. The U3 has 16 "flexible" inputs which can be configured for any mix and analogue, digital input or digital output making for a very versatile general purpose DAQ unit. The U3 is supplied with a wide range of FREE Data logging software and examples for use with most programming and DAQ packages.

The LabJack U3 can have up to 16 analogue inputs available on the flexible I/O lines. Single-ended measurements can be taken of any line compared to ground, or differential measurements can be taken of any line to any other line. Analogue input resolution is 12-bits with an input range of 0-2.4 volts. Optional signal conditioning adaptors are available that can condition the inputs to 0-5V, 0-10V or 4-20mA.

The LabJack U3 can have up to 20 digital I/O channels. 16 are available from the flexible I/O lines, and 4 are dedicated digital I/O. Each digital line can be individually configured as input, output-high, or output-low. The digital I/O use 3.3 volt logic and are 5 volt tolerant. Up to 2 flexible I/O lines can be configured as timers. The timers are very flexible, providing options such as Pulse Width Modulated output, pulse timing, pulse counting, and quadrature input from encoders. Up to 2 flexible I/O lines can be configured as 32-bit counters.

The LabJack U3 also has 1 or 2 dedicated analogue outputs which can be set to provide an output voltage between 0 and 5 volts with 8-bits of resolution.

The LabJack U3 is supplied with a range of free software. The LabJack Control Panel application handles configuration and testing of the U3. When first opened it searches for connected LabJacks and displays a panel whereby all the I/O types can be configured. The application also displays analogue/digital inputs and has boxes to set analogue/digital outputs. The U3 has field upgradeable flash memory. The self-upgrade application programs the latest firmware into the processor. FREE firmware upgrade will be available from time to time bringing improved performance and new features.

The U3 is also supplied with a copy of DAQFactory Express data acquisition and control, software. DAQFactory Express offers data logging, user designable screens with trending, automation capabilities and more. The U3 is also supported by the RealView Chart recorder software and the ProfiLab-Express programming package.

For programmers, the U3 is supplied with Visual C and Visual Basic modules for the LabJackUD driver, and simple example projects. A LabVIEW VI is also supplied.

The U3 is rugged and is designed for industrial use: the operating temperature range is -40°C to + 85°C and all I/O are overload and short-circuit protected. The ABS enclosure has screw mounting attachments and optional DIN rail mounting clips.

Available ex-stock from Audon Electronics for £69

Low cost USB Based temperature and Humidity Sensor

2007-06-14T03:08:00.000-07:00

Now available from Audon Electronics is the DLP-TH1, a USB-based temperature and humidity sensor. The DLP-TH1 sensor is supplied with free Windows software that displays temperature, humidity, and dew-point data in both Celsius and Fahrenheit scales, plots data graphically to the screen, and logs to an Excel compatible data file on the hard drive. The software will also send an email to user-specified recipients if the temperature or humidity exceeds specified alarm setpoints.

The DLP-TH1 sensor uses a fully calibrated capacitive polymer-sensing element for relative humidity with a 0-100% range and a bandgap temperature sensor providing excellent long-term stability with a -40° to + 120°C range. Calibration coefficients for the sensors are permanently stored in digital memory within the DLP-TH1 module so that the module is fully interchangeable with any other DLP-TH1 module.

The DLP-TH1 is shipped with Windows 98/ME/2000/XP compatible software and USB drivers and there is also an ActiveX and LabVIEW VI's. No external power source is required as all power is taken from the USB port via the provided 2M USB cable. Up to 20 DLP-TH1 sensors can be connected to a single PC through USB hubs. Typical applications include monitoring temperature and humidity in Server/Host rooms, hydroponics labs and greenhouses and museum display cabinets.

UE9 is Power-House of Analogue and Digital I/O

2007-06-14T03:04:00.000-07:00

The New LabJack UE9 available from Audon Electronics is a power-house of analogue and digital I/O. Whats more, it can connect to both USB AND Ethernet Systems.

The UE9 boast 14 analogue inputs, 2 analogue outputs and 23 digital I/O. The UE9 can connect to a host PC via a USB 1.1 or 2.0 interface or it can connect to a LAN via its Ethernet 10baseT Interface.

Each analogue input can be configured individually as unipolar 0-5 volts or bipolar ±5 volts. An internal PGA provides gains of 1, 2, 4, or 8 (unipolar ranges only at this time). Analogue input resolution is user adjustable; 12-bits at max speed of 50kHz increasing up to 16-bits at slower speeds. It is possible to connect thermocouples directly to the UE9, if you don't require great accuracy: a resolution of ±1 °C is achievable. The UE9 has an internal temperature sensor, which can be used for cold junction compensation. There are two 12-bit analogue outputs offering a 0-4.096V range.

The LabJack UE9 has 23 digital I/O channels which can be individually configured as input, output-high, or output-low. 8 of these lines are called flexible digital I/O (FIO) and can be software configured as up to 6 timers and 2 counters. The timers are very flexible, providing options such as Pulse Width Modulation output for motor control, pulse timing, and quadrature input for motor applications. Up to 2 FIO can be configured as 32-bit counters.

The UE9 is supplied with a free licensed copy of the DAQFactory Express software. This software provides allows you to create your own operator screens using up to 10 built-in components such as chart displays, bar charts etc, allows datalogging and you can even create simple automated control scripts. A collection of DAQFactory applications are also provided to get you started, showing how to acquire slow and high speed data, set the digital I/O and also how to set up a PWM output channel. DAQFactory Express can be upgraded to higher versions of DAQFactory if you require addition functionality such as alarms and PID control.

Also provided are LabVIEW VI's and sample applications in Visual Basic and C.

The UE9 has been designed for both experimental and industrial use. It is rated for use over an industrial temperature range and has built-in mounting fixtures. A selection of I/O are available at screw terminals and all I/O are routed to side mounted D-type connectors; A screw terminal board is available.

The USB myPCLab DAQ Units has Universal Inputs

2006-11-16T02:24:00.000-08:00

Available from Audon Electronics is the myPCLab USB
data acquisition unit which accepts thermocouples, PT100
temperature probes, Volts and 4-2OmA loops all for under
£60.



myPCLab is a very compact Data Acquisition tool which connects
to a PC via a USB port and monitors two universal analogue inputs,
accepting thermocouples, Ptl 00, Voltages and 4-2OmA current
loops along with one digital input. Sampling rate can be up to 128
samples per second and ADC resolution is user adjustable from
11 to 15 bits. There is built-in thermocouple and P11 00 linearisation
and automatic thermocouple cold-junction compensation.

The myPCLab comes with an intuitive and easy-to-use Windows
data logger software package which plots data, shows gauges,
bargraphs and digital readouts and logs data to disk. Logged data
can be exported in multiple file formats (xis, pdf, rtf, xml, html,dbf,
txt, csv) for easy importation to analysis and Spreadsheet packages.

The myPCLab software can simultaneously communicate with multiple
modules, making it easy to expand the number of inputs of a
measurement system.



Although the myPClab is USB based, it actually uses a virtual RS232
Com port, so any software package that can talk to a Corn port can
communicate with the myPClab. There are two communications
modes, ASCII text and Modbus.

With ASCII text Auto-send, data is transmitted from the myPClab
in a simple comma separated ASCII text format at a pre-set time
interval. Data can be read using any package capable of accepting
ASCII strings including most daq packages such as LabVIEW, VEE,
DAoFactory, TestPoint etc, programming languages VB, Delphi,
C++ .NET, and terminal programs such as HyperTerminal.

In MODBUS RTU Slave mode, myPCLab acts as a Modbus RTU
slave that can answer to Read Holding Register requests, Modbus
command number 3. The module doesn t have a specific Modbus
address, since it s the only device in its serial port. It will answer to
read request to any valid slave address. It can therefore be used
with every SCADA software package that support MODBUS RTU.

For more information, please contact :-

Audon Electronics
123 High Road, Chilwell, Nottingham NG9 4AT. UK
Tel: +44 (0)115 925 8412
Fax +44 (0) 115 925 9757
Web: www.audon.co.uk

LabJack U12 USB DAQ Unit

2006-11-15T08:23:00.000-08:00

Now available in the UK from Audon Electronics is the LabJack U12 USB data acquisition and control unit.

The Labjack features 8 single ended or 4 differential analogue inputs,
2 analogue outputs, 20 digital I/O including a 32 bit counter and
watchdog timer. This is all crammed into a sturdy unit measuring only
150mm x 110mm x 35mm. 

The LabJack has a ±10V input range at 12-bit resolution. Differential
channels can make use of the low noise precision amplifier with gains
of 1,2,4,8,16,20, giving an effective resolution of greater than 16-bits.
Data can be streamed to disk at 1kHz and a bursts mode allows over
4000 samples to de taken at a 8kHz rate. The two 0-10V analogue
output channels can be updated at a 50Hz rate with 10-bit resolution.
All analogue I/O are accessed via screw terminals.

The LabJack has 20 digital I/O channels which can be individually
configured as input or output. Four digital I/O's are accessed via
screw terminals whilst the remaining 16 are accessed through a
25-way D connector; an optional relay/opto-isolator expansion
board is available.There is also one 32-bit counter available on
the LabJack U12, capable of counting frequencies up to 1 MHz. 
The LabJack U12 also has a watchdog timer function available
which can change the states of digital I/O if the LabJack does not
successfully communicate with the PC within a specified time-out
period. This function could be used to reboot the PC allowing for
reliable unattended operation.

The use of the PC's USB port allows for a simple plug-and-play
installation process and by using USB hubs, up to 80 LabJacks
may be connected to a single USB port.

Included with the LabJack are the free example applications
LJlogger and LJscope. LJlogger provides datalogger type
functionality. It reads all inputs, controls all outputs, writes real
time data to the Internet or hard disk, and sends email when
events are triggered. LJscope is a virtual oscilloscope program
with FFT display.

Drivers are provided as a DLL which can be called from most
programming languages. Also included are an ActiveX wrapper
and LabVIEW VIs which call all the functions in the DLL.